Previous Page | Next Page Contents Glossary Index


About this book
Notation conventions
Publications guide
Introducing the printer
Functional areas
About forms and forms path
About the control unit area
About the printer operator panel
About the developer
About the forms input area and transfer station area
About the printer control panel
About the splicing table
About the transfer station control lever and tractor control knob
About the vacuum, stack height, and puller controls
About the fuser entry area
About the stacker area
About the rear service area
Operator's overview
Operator responsibilities
Normal operation (Ready status)
Operator intervention (Not Ready status)
Service call procedure
Using the touchscreen
The Enhanced Operator Console
Tabs, buttons, and panels
Adjusting the touchscreen
User controls
On-screen-display controls
Problem resolution
Operating the printer
Controlling the system power
Local/remote power control
Powering on the system
Powering off the system
Shutting down and restarting the system
Shutting down the system
Restarting the system
Configuring the printer
Configuring remote access
Configuring e-mail traces
Configuring attachments
Enabling and disabling attachments
Remote channel enable/disable
Local channel enable/disable
Enabling and disabling pre/postprocessors
Configuring pre/postprocessors
Canceling a job
Authorization levels
Changing access levels and passwords
Managing and defining new users
Loading configuration from diskette
Adjusting the volume of the operator alert assembly
Connecting an accessory to the operator alert contacts
Reporting printer usage
Switching printer modes (dual simplex/duplex) and printer speed
Switching from duplex to dual simplex mode
Switching from dual simplex to duplex mode
Switching printer speeds
Working with forms
Viewing Snapshots
Sorting and searching Snapshots
Loading a Snapshot
Saving changes to Snapshots
Saving a new Snapshot
Deleting a Snapshot
Restoring Snapshot settings from diskette
Loading forms--auto load (dual simplex mode)
At the touchscreen or the printer operator panel
At the printer forms input area
At the touchscreen
At the stacker control panel
At the printer control panel (tractored forms)
At the printer control panel (tractorless forms or no Auto Load controls)
At the printer
At the touchscreen or the printer control panel
Loading forms--auto load (duplex mode)
Loading forms without manual reload--auto load (duplex mode)
Feeding new forms through the printer
Adjusting the printer for new forms
Loading the correct forms settings
Loading forms--semiautomatic load (dual simplex mode)
Checking the tension arm
Adjusting the upper and lower tension arm springs on the Infoprint 4000
Adjusting the lower tension arm spring for the Infoprint 4100
Splicing forms on the Infoprint 4000
Splicing forms on the Infoprint 4100
Splicing tractorless forms
Aligning tractored forms
Forms loaded through both printers
Forms are not loaded in Printer 2
Forms are broken between the printers
Aligning tractorless forms
Threading the Buffer/Flipper Unit (duplex)
Straight line configuration
Left angle configuration
Setting print registration
Using the NPRO function to advance forms
NPRO procedure
NPRO Advance One Page procedure
Checking for a front-facing page
Checking forms alignment
Checking print quality
Engine print balancing procedure
Unloading the stacker
Using the printer stacker with a postprocessor
Verifying synchronized duplex printing
Taking care of problems
Responding to messages
Operator message codes
Intervention messages
0133 Skew error
0119 Upper tractor forms jam
079A, 0131, 0132 Tension errors
D720 Verification mark position incorrect
0134 Fuser wrap
0093 Input loop paper jam
0161 Stacker jams
Hard program checks
Status messages
Forms jams
Forms jam is visible
Forms jam is not visible
Stacker forms jam
Transfer station area forms jam
Upper fuser forms jam
Stacker pendulum forms jam
Forms jam between Printer 1 and Printer 2
Jams between the printer and a postprocessing device
Forms jam in the postprocessing device
Clearing the forms path
Transfer Station area
Fuser area and Stacker area
Stacker and Pendulum area
Recovering from a forms jam
Suggestions for preventing jams
Running traces
Print quality problems
Sudden failures
Problem solving tips and suggested actions
Maintaining the printer
Cleaning the printer
Developer area
Forms input area
Transfer station area
Stacker area
Buffer/Flipper unit
Rear service area
Adding fuser oil
Adding toner
Adding toner bottles (Infoprint 4000)
Adding a toner cartridge (Infoprint 4100)
Checking the toner collector
Changing the toner collector
Changing the developer mix
Checking the fine filter
Changing the fine filter
Cleaning the oiler belt
Changing the oiler belt
Checking the absorbent pad in the oil pan
Adding supplies
Obtaining supplies
Appendix. Features
Move Mark Forms Feature (RPQ 8B3964)
Mark Perforation on Perfless Paper Feature (RPQ 8B3965)
Enabling long forms
Signature Page Feature (FC 8B4053)
No forms size error checking
Changing the Customer Changeable Developer (CCD)
Removing the developer
Installing the developer
Magnetic ink character recognition (MICR) CCD
Using the Infoprint 4000/4100 to print MICR documents
Setting up the printer for printing with MICR toner
MICR fonts
MICR format requirements
MICR quality control
MICR quality and format verification
Inline Densitometer for High Resolution Printers Feature (FC 4832)
Threading the densitometer unit
Adjusting print density
Inline Densitometer for Low Resolution Printers Feature (FC 4833)
Threading the densitometer unit
Adjusting print density
Forms Identification (Barcode) Feature (FC 4464)
Defining a form barcode
Loading pre-printed barcode forms
Cleaning the Forms Barcode Sensor
Problem resolution
Stacker Basket Feature (FC 4775)
Using highlight color with the Infoprint 4000 and Infoprint 4100
Aligning the printhead
Considering print registration
Planning the application
Application considerations
Threading the printer (side 1 to side 1)
Universal Printer Pre- and Postprocessing Interface (UP3I) (FC 4730)
Adjusting the paper guides for lightweight paper
Infoprint Manager Operations for AIX on the Enhanced Operator Console Feature (FC 4560)
Enabling the TCP/IP attachment
Using the Infoprint Manager Operations GUI from the printer console
Preheat Platen Teflon Mat (RPQ 8B5023)
Installing the teflon mat and wear strip
Removing the teflon mat and wear strip assembly
Product Recycling and Disposal
Communication Statements